Teledu 8pcs Front Suspension Kit Ball Joints Sway Bars Kit For Dodge Dakota Durango

7.Insert new stabilizer link at suspension strut 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer Tip:Secure the ball stud against twisting with a suitable tool 9.Insert new stabilizer link at stabilizer 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension 12.Conclude with a test drive Tie-Rod End Replacement Guideline: This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance 1.Lift the vehicle and dismount the front axle wheels 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes 3.Dismount the front underride guard 4.Loosen the fastening nut from the tie rod and remove it completely 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator 6.Remove the clamp of the bellow on the steering gear 7.Push the bellow towards the tie rod end 8.Unscrew the inner tie rod from the rack 9.Clean the sealing face of the bellow at the steering gear 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle Note:Always use new self-locking nuts and bolts for a reliable repair 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer 12.Mount the bellow and close the clamps with the appropriate special tool Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure 14.Mount the front underride guard 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications 17.Perform a test drive Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car (3).What happens if I don\'t replace ball joints? (4).Do I need to grease new ball joints? Brand: Unbrand Manufacturer Part Number: E81042201CP Interchange Part Number: K7242 K7274 K7241 ES3399T Placement on Vehicle: Front, Left, Right, Upper, Lower Surface Finish: Polished, Rust Protected Custom Bundle: Yes Greasable or Sealed: Greasable Modified Item: Yes Superseded Part Number: Front Driver and Passenger Side Replacement Type: Sway Bar Link Universal Fitment: No Items Included: Mounting Hardware OE/OEM Part Number: Suspension Steering Tie Rod Ends Linkages Assembly,Ball Joint Manufacturer Warranty: 10 Year OE Spec or Performance/Custom: OE Spec Quantity: 8 Pcs Cross Reference Part Number: 1997 1998 1999 Fitment: For Dodge Dakota and Durango Kit Parts Included: Ball Joint Tie Rod End Sway Bar Link Features: Greasable